GOLFMK8
GOLFMK7
GOLFMK6
GOLFMKV

Retrofitting Blind Spot Assist / Side Assist

Dynamic

New member
Location
It
Car(s)
Golf 7.5 Gti
Buon pomeriggio ragazzi, grazie a Dio, sono riuscito a far funzionare il sistema dal punto cieco, il problema era quello che sospettavo, la versione del firmware era diversa dalla versione di parametrizzazione, la mia versione di firmware era ( A ) e la versione di parametrizzazione era ( C ), quindi è stato necessario aggiornare il firmware del modulo 5QD907686A. Ho scaricato l'aggiornamento a 5Q0907686C e installato un altro pacchetto di parametri. Tutto ha funzionato normalmente. Ringrazio tutti!
ciao Luiz penso di avere il tuo stesso problema, come faccio ad aggiornare il firmware?
 

Luiz Henrique

Ready to race!
Location
Brazil
Car(s)
GTI
ciao Luiz penso di avere il tuo stesso problema, come faccio ad aggiornare il firmware?
Good evening @Dinamic, basically you will need two tools: the firmware file, VAS5054a and Odis E. It's pretty simple, but I think what will be more work is if you don't have the VAS5054a! Do you have the VAS5054a?
 

Dynamic

New member
Location
It
Car(s)
Golf 7.5 Gti
Buonasera @Dinamic, penso che avrai bisogno di due strumenti: il file del firmware, VAS54a e Odis E. È piuttosto semplice, ma che ciò sarà più lavoro è se non hai il VAS5054a! Hai il VAS5054a?
Luiz potresti condividere il firmware e la procedura?
 

Gust

New member
Location
Belgium
Car(s)
2015 Golf GTI perf
So, it's been a while when I got around the installation of the hardware for this. Now I finally got a new official VCDS cable, wanted to do the coding for it.
I did everything as described in the spanish XaGiCo file, but then I get a whole bunch of errors, all in the ABS controller, two of it mentioning wheel speed sensor. Are these to be replaced before coding? Also getting errors about electronic parking brake, and TPMS. I have the 'oldschool' tpms, no sensors inside the wheels..

Anybody else ran into these issues?

When reversing all the coding changes i made for the BSM, everything is back to normal and brakes function normally without errors.

Grtz,
G
 

IWMTom

Autocross Newbie
So, it's been a while when I got around the installation of the hardware for this. Now I finally got a new official VCDS cable, wanted to do the coding for it.
I did everything as described in the spanish XaGiCo file, but then I get a whole bunch of errors, all in the ABS controller, two of it mentioning wheel speed sensor. Are these to be replaced before coding? Also getting errors about electronic parking brake, and TPMS. I have the 'oldschool' tpms, no sensors inside the wheels ..

Anybody else ran into these issues?

When reversing all the coding changes i made for the BSM, everything is back to normal and brakes function normally without errors.

Grtz,
G.
You need to change the ABS sensors for RCTA if you don't have ACC from factory.
 

Gust

New member
Location
Belgium
Car(s)
2015 Golf GTI perf
So finally managed to install the abs sensors, and coded everything again. No more issues in the abs controller for now. But after doing a little test drive, things don't work at all. After shutting down the car, and restart, it gives an error message the blind spot system is unavailable. Did another scan with VCDS, which shows me errors in 10 and 3C:

Code:
Adres 10: Parkeerhulp (J446)       Labels:| 5Q0-919-294.clb
   Onderdeel No SW: 5Q0 919 294 K    HW: 5Q0 919 294 A
   Component: PARKHILFE 8K  H03 0054 
   Revisie: --------    Serienummer: 39391517005377
   Codering: 0071155051
   Werkplaats#: WSC 01357 011 00200
   ASAM Dataset: EV_EPHVA18AU3700000 002026
   ROD: EV_EPHVA18AU3700000_002_VW37.rod
   VCID: 43D2B1486B172B03D21-8016

1 Fout Gevonden:
13688835 - Databus ontvangen storingswaarde
          U1123 00 [009] - -
          [Steuergerät für Rear Cross Traffic Alert - RCTA_01.RCTA_Status - Fehlerspeicher auslesen]
          Bevestigd - Getest sinds Geheugen Wissen
             Bevries Frame:
                    Fout Status: 00000001
                    Fout Prioriteit: 6
                    Fout Frekwentie: 1
                    Reset teller: 80
                    Kilometrage: 67906 km
                    Datum: 2022.01.23
                    Tijd: 16:27:56

Code:
Adres 3C: Rijstr.wisselhulp (J1086)       Labels:* Geen
   Onderdeel No SW: 5QD 907 686 A    HW: 5QD 907 686
   Component: HRE_Master    H12 0080 
   Serienummer: 6107297939
   Codering: 02011103
   Werkplaats#: WSC 12345 123 12345
   ASAM Dataset: EV_HREntryHella 001028
   ROD: EV_HREntryHella_VW37.rod
   VCID: 4FFA8D78B75FDF63469-801A

   Regelapparaat 2 voor rijstrookwisselassistent:
   Subsysteem 1 - Onderdeel No SW: 5QD 907 685 A    HW: 5QD 907 685
   Component: HRE_Slave  H12 0080
   Serienummer: 6107012947         
   Codering: 020111

1 Fout Gevonden:
267520 - Ongeldig gegevensrecord
          B2005 00 [009] - -
          [Control Unit - Invailed dataset]
          Bevestigd - Getest sinds Geheugen Wissen
             Bevries Frame:
                    Fout Status: 00000001
                    Fout Prioriteit: 3
                    Fout Frekwentie: 1
                    Reset teller: 80

This means i need to find the correct dataset/labelfile for the module? Is this even possible with VCDS? Also have an old VCP somewhere, but it's not activated anymore...
 

Luiz Henrique

Ready to race!
Location
Brazil
Car(s)
GTI
So finally managed to install the abs sensors, and coded everything again. No more issues in the abs controller for now. But after doing a little test drive, things don't work at all. After shutting down the car, and restart, it gives an error message the blind spot system is unavailable. Did another scan with VCDS, which shows me errors in 10 and 3C:

Code:
Adres 10: Parkeerhulp (J446)       Labels:| 5Q0-919-294.clb
   Onderdeel No SW: 5Q0 919 294 K    HW: 5Q0 919 294 A
   Component: PARKHILFE 8K  H03 0054
   Revisie: --------    Serienummer: 39391517005377
   Codering: 0071155051
   Werkplaats#: WSC 01357 011 00200
   ASAM Dataset: EV_EPHVA18AU3700000 002026
   ROD: EV_EPHVA18AU3700000_002_VW37.rod
   VCID: 43D2B1486B172B03D21-8016

1 Fout Gevonden:
13688835 - Databus ontvangen storingswaarde
          U1123 00 [009] - -
          [Steuergerät für Rear Cross Traffic Alert - RCTA_01.RCTA_Status - Fehlerspeicher auslesen]
          Bevestigd - Getest sinds Geheugen Wissen
             Bevries Frame:
                    Fout Status: 00000001
                    Fout Prioriteit: 6
                    Fout Frekwentie: 1
                    Reset teller: 80
                    Kilometrage: 67906 km
                    Datum: 2022.01.23
                    Tijd: 16:27:56

Code:
Adres 3C: Rijstr.wisselhulp (J1086)       Labels:* Geen
   Onderdeel No SW: 5QD 907 686 A    HW: 5QD 907 686
   Component: HRE_Master    H12 0080
   Serienummer: 6107297939
   Codering: 02011103
   Werkplaats#: WSC 12345 123 12345
   ASAM Dataset: EV_HREntryHella 001028
   ROD: EV_HREntryHella_VW37.rod
   VCID: 4FFA8D78B75FDF63469-801A

   Regelapparaat 2 voor rijstrookwisselassistent:
   Subsysteem 1 - Onderdeel No SW: 5QD 907 685 A    HW: 5QD 907 685
   Component: HRE_Slave  H12 0080
   Serienummer: 6107012947        
   Codering: 020111

1 Fout Gevonden:
267520 - Ongeldig gegevensrecord
          B2005 00 [009] - -
          [Control Unit - Invailed dataset]
          Bevestigd - Getest sinds Geheugen Wissen
             Bevries Frame:
                    Fout Status: 00000001
                    Fout Prioriteit: 3
                    Fout Frekwentie: 1
                    Reset teller: 80

This means i need to find the correct dataset/labelfile for the module? Is this even possible with VCDS? Also have an old VCP somewhere, but it's not activated anymore...
did you parameterize your master module? I suggest you update the firmware to version C and parameterize the master module. remembering that for firmware update and parameterization you will need VAS 5054 and Odis E.
 

Gust

New member
Location
Belgium
Car(s)
2015 Golf GTI perf
No I haven't updated or parameterized anything yet, never done such thing.
Where to find this firmware?
 

Gust

New member
Location
Belgium
Car(s)
2015 Golf GTI perf
So for doing this I need other tools then just vcds? Could it be done with VCP? I haven't got this Vas or odis
 
Top